I cut out the pieces above for my first couple of squares and I can’t wait to piece them together. The fabrics are Moda’s Hoopla Cross Weave in Green and Kona Jungle. All my solids were purchased from the Simply Solid Fabric store on Etsy, and I was really happy with them.
Below is a preview of some of my other fabric pairings.
Stay tuned for more!
I used Alexander Henry Heath in Chocolate for the binding and I really like how it looks with the rest of the quilt.
Next, spread the quilt top on top of the batting like so…
Then, starting from the top, roll the 2 together and set aside.
Next, lay the quilt back down with the right side facing down. Also make sure that the top and bottom are oriented correctly.
Then, take some masking tape and tape the edges. Pull the fabric somewhat taut as you go so there are no wrinkles, but not so much that it becomes warped. We are NOT trying to channel Joan Rivers’ plastic surgeon here. I find that the best way to do this step is to start by taping the top. Then, I work down the sides together. Then I end by taping the bottom. You will probably want to use enough tape to cover almost all the edges or else it may not stick to the floor well as you’re putting tension on the fabric.
Once your quilt back is taped, starting from the bottom, roll out the backing and quilt top.
Here it is all the way rolled out…
Now the final part of this step is to pin all 3 layers together. I use curved safety pins because they make it really easy to grab all 3 layers.
I like to start in the center and spiral my way out. The key to this step is to smooth out the quilt top as you pin so that you get rid of the wrinkles but not so much that the fabric becomes warped. Again, NO Joan Rivers! It’s ok to sit/kneel on your quilt during this step. This is probably one of the most tedious steps in the whole quilting process, but once you’re done with this step, you can untape the quilt and carefully put it on your lap and imagine what it will be like when you are done with making the quilt. Remember to not go super crazy with your excitement of trying the quilt because it may undo some of that smoothing you just spent time doing. I like to leave a couple of inches of batting and the quilt back extending beyond the quilt top. I think that that makes the quilting process a bit easier.
Next up will be the quilting itself.
To create this quilt back, here’s what I did. I took 2 yds of the Metro Living Lantern, and cut it in half. I had about 3/4 yd of the Quilter’s Linen left over, so I cut that in half and sewed it to each of the halves of the Lantern fabric. I then cut 1 1/2 inch strips from the Kona Aqua, sewed them end to end to create a long enough strip to span the width of the quilt back and sewed that to the Quilter’s Linen. Now I was left with 2 large pieces of fabric (seen at the top and bottom of the quilt back). I placed my completed quilt top on the ground and then I placed these pieces I just created over the top and bottom of the quilt top with about an inch overhanging on all sides. Now I could see how much space was in the middle that I needed to fill with other fabric. Turns out I needed a strip about 12 inches long to fill the gap.
From the leftover printed fabric that I had from the front (Alexander Henry’s Natura Collection), I cut 6 pieces that measured 6.5″ x 12.5″. I also cut 1.5″x 12.5″ strips from the Kona Aqua as sashing between the printed fabric. I sewed these together as shown below. I then figured out how much more fabric I needed to fill the edges with the Quilter’s Linen and sewed these on to the ends. I then sewed this middle strip to the top and bottom pieces. Now onto the quilting and the binding!
For this quilt, I picked the Kitchen Windows Pattern. The printed patterns come from the Natura Collection by Alexander Henry that I’ve had stashed away for a few years. The blue solid is Kona Cotton in Aqua and the tan is Quilter’s Linen in Straw (both by Robert Kaufman).
It’s by no means a perfect quilt, but I am proud of how much better my corners met up on this quilt compared to the last.
Now I just have to figure out how I want to do the back. I’ve got some Metro Living Lantern in Leaf that I want to use, and I think I’ll somehow incorporate leftover scraps from the fabrics above along with it. It may be another few months until I post about the back, but stay tuned!
Yes, ladies and gentlemen, I have taken up quilting. This is Eunice writing, of course. Now, you may wonder what possesses someone in their 20s to resort to an activity embraced mostly by ladies in their 70s. But, as I stumbled across some quilting blogs (like this one and this one and even this one), I couldn’t help but be inspired.
I once made a quilt a long time ago, but really this should be considered my first quilt. I had bought some Heather Ross Mendocino fabric a few years ago without knowing what to do with it. This seemed like the perfect way to use it. This is a very simple quilt using this nine-patch pattern. I tried my hand at machine stippling and despite some errors, I’m really pleased with how it turned out.
Also, here’s a preview of what’s to come…
Finally, here are some gratuitous dog pics. Dwight’s not super-excited, he’s just yawning.
I used some old pillow forms we had, destuffed them and then restuffed them. The pillows are basically 2 18″x18″ panels sewn together and then stuffed with the rejuvenated pillow forms. No zippers or flaps. I just hand-sewed the bottoms of the pillows.